Differences

This shows you the differences between two versions of the page.

--- 184_notes:examples:week7_ohms_law [2017/10/03 23:46] – created tallpaul
+++ 184_notes:examples:week7_ohms_law [2018/06/19 14:54] (current) – curdemma
@@ Line 1: / Line 1: @@
-=====Example: Application of Node Rule=====
+[[184_notes:resistivity|Return to resistors and conductivity]]
-Suppose you have the circuit below. Nodes are labeled for simplicity of discussion. you are given a few values:  $I_1=8 \text{ A}$ ,  $I_2=3 \text{ A}$ , and  $I_3=4 \text{ A}$ . Determine all other currents in the circuit, using the [[184_notes:current#Current_in_Different_Parts_of_the_Wire|Current Node Rule]]. Draw the direction of the current as well.
-{{ 184_notes:6_nodes.png?300 |Circuit with Nodes}}
+=====Example: Application of Ohm's Law=====
+Suppose you have a simple circuit that contains only a 9-Volt battery and a resistor of  $120 \Omega$ . What is the current in the wire?
 ===Facts===
-  * $I_1=8 \text{ A} $,$ I_2=3 \text{ A}$, and  $I_3=4 \text{ A}$ .
+  * $\Delta V = 9\text{ V}$
-  * $I_1 $,$ I_2 $, and$ I_3$ are directed as pictured.
+  * $R = 120 \Omega$
 ===Lacking===
-  * All other currents (including their directions).
+  * Current
 ===Approximations & Assumptions===
-  * The current is not changing (circuit is in steady state).
+  * The wire has very very small resistance when compared to the 120  $\Omega$  resistor.
-  * All current in the circuit arises from other currents in the circuit.
+  * The circuit is in a steady state.
-  * No resistance in the battery (approximating the battery as a mechanical battery)
+  * Approximating the battery as a mechanical battery.
+  * There is no outside influence on the circuit.
 ===Representations===
-  * We represent the situation with diagram given.
+  * We represent [[184_notes:resistivity#Resistance|Ohm's Law]] as  $\Delta V = IR$ .
-  * We represent the Node Rule as $I_{in}=I_{out}$.
+  * We represent the situation with following circuit diagram.
+[{{ 184_notes:7_ohm.png?300 |Circuit with Resistor}}]
 ====Solution====
-Let's start with node  $A$ . Incoming current is  $I_1$ , and outgoing current is  $I_2$ . How do we decide if  $I_{A\rightarrow B}$  is incoming or outgoing? We need to bring it back to the Node Rule: $I_{in}=I_{out}$. Since  $I_1=8 \text{ A}$  and  $I_2=3 \text{ A}$ , we need  $I_{A\rightarrow B}$  to be outgoing to balance. To satisfy the Node Rule, we set
+We have assumed that the battery and the wire contribute negligible resistance to the circuit. So the resistance of the circuit is simply the resistance of the resistor: $R = 120\Omega$. These assumptions also lead us to conclude that the voltage that is provided by the battery is used up only in the resistor (and not on the wires). So the potential difference across the resistor is the entire 9 Volts, so $\Delta V = 9 \text{ V}$. We can now use Ohm's Law to find the current through the circuit: $$I = \frac{\Delta V}{R} = 75 \text{ mA}$$
- $I_{A\rightarrow B} = I_{out}-I_2 = I_{in}-I_2 = I_1-I_2 = 5 \text{ A}$
-We do a similar analysis for node  $B$ . Incoming current is  $I_{A\rightarrow B}$ , and outgoing current is  $I_3$ . Since  $I_{A\rightarrow B}=5 \text{ A}$  and  $I_3=4 \text{ A}$ , we need  $I_{B\rightarrow D}$  to be outgoing to balance. To satisfy the Node Rule, we set
- $I_{B\rightarrow D} = I_{out}-I_3 = I_{in}-I_3 = I_{A\rightarrow B}-I_3 = 1 \text{ A}$
-For node  $C$ , incoming current is  $I_2$  and  $I_3$ . There is no outgoing current defined yet!  $I_{C\rightarrow D}$  must be outgoing to balance. To satisfy the Node Rule, we set
-$$I_{C\rightarrow D} = I_{out} = I_{in} = I_2+I_3 = 7 \text{ A}$$
-Lastly, we look at node $D$. Incoming current is  $I_{B\rightarrow D}$  and  $I_{C\rightarrow D}$ . Since there is no outgoing current defined yet,  $I_{D\rightarrow battery}$  must be outgoing to balance. To satisfy the Node Rule, we set
-$$I_{D\rightarrow battery} = I_{out} = I_{in} = I_{B\rightarrow D}+I_{B\rightarrow D} = 8 \text{ A}$$
-Notice that  $I_{D\rightarrow battery}=I_1$ . This will always be the case for currents going in and out of the battery (approximating a few things that are usually safe to approximate, such as a steady current). In fact, we could have treated the battery as another node in this example. Notice also that if you incorrectly reason about the direction of a current (incoming or outgoing), the calculation will give a negative number for the current. The Node Rule is self-correcting. A final diagram with directions is shown below.
-{{ 184_notes:6_nodes_with_arrows.png?300 |Circuit with Nodes}}