Differences

This shows you the differences between two versions of the page.

--- 184_notes:examples:week7_resistance_wire [2017/10/04 15:56] – [Resistance of a Wire] tallpaul
+++ 184_notes:examples:week7_resistance_wire [2018/06/19 14:54] (current) – curdemma
@@ Line 1: / Line 1: @@
+[[184_notes:resistivity|Return to resistors and conductivity]]
 =====Resistance of a Wire=====
-Suppose you have a wire whose resistance you know. The wire has a length of 2 cm, and has a cross-sectional area of 1 mm$^2 $. The resistance of the wire is 50 m$ \Omega$. What is the resistance if you increase the length of the wire to 6 cm? What if you increase the cross-sectional area to 3 mm $^2$ ?
+Suppose you have a wire whose resistance is 60 m $\Omega$ . The wire has a length of 2 cm, and has a cross-sectional area of 1 mm $^2$ . What would be the resistance if you increase the length of the wire to 6 cm (keeping the area the same)? What would be the resistance if you increase the cross-sectional area to 3 mm $^2$  (keeping the original length of wire)?
 ===Facts===
-  * The original wire has  $L = 2 \text{ cm}$ ,  $A = 1 \text{ mm}^2$ , and $R = 50 \text{ m}Omega$.
+  * The original wire has  $L = 2 \text{ cm}$ ,  $A = 1 \text{ mm}^2$ , and $R = 60 \text{ m}\Omega$.
-  * The length could be increased to $L_{new} = 4 \text{ cm}$.
+  * The length could be increased to $L_{new} = 6 \text{ cm}$.
   * The cross-sectional area could be increased to  $A_{new} = 3 \text{ mm}^2$ .
@@ Line 15: / Line 17: @@
 ===Representations===
-  * We represent the resistance of a simple wire such as this with:  $R = \frac{L}{\sigma A}$
+  * We represent the resistance of a simple wire with:  $R = \frac{L}{\sigma A}$
 ====Solution====
-Let's start with node  $A$ . Incoming current is  $I_1$ , and outgoing current is  $I_2$ . How do we decide if  $I_{A\rightarrow B}$  is incoming or outgoing? We need to bring it back to the Node Rule:  $I_{in}=I_{out}$ . Since  $I_1=8 \text{ A}$  and  $I_2=3 \text{ A}$ , we need  $I_{A\rightarrow B}$  to be outgoing to balance. To satisfy the Node Rule, we set
+All we need here is our representation for the resistance of the wire. In the first change to the wire, we triple it's length ($2 \text{ cm} \rightarrow 6 \text{ cm}$). Our new resistance then is found by $$R_{new} = \frac{L_{new}}{\sigma A} = \frac{3L}{\sigma A} = 3R = 180 \text{ m}\Omega$$
-$$I_{A\rightarrow B} = I_{out}-I_2 = I_{in}-I_2 = I_1-I_2 = 5 \text{ A}$$
-We do a similar analysis for node  $B$ . Incoming current is $I_{A\rightarrow B}$, and outgoing current is  $I_3$ . Since $I_{A\rightarrow B}=5 \text{ A} $and$ I_3=4 \text{ A} $, we need$ I_{B\rightarrow D}$ to be outgoing to balance. To satisfy the Node Rule, we set
-$$I_{B\rightarrow D} = I_{out}-I_3 = I_{in}-I_3 = I_{A\rightarrow B}-I_3 = 1 \text{ A}$$
-For node  $C$ , incoming current is  $I_2$  and  $I_3$ . There is no outgoing current defined yet! $I_{C\rightarrow D}$ must be outgoing to balance. To satisfy the Node Rule, we set
-$$I_{C\rightarrow D} = I_{out} = I_{in} = I_2+I_3 = 7 \text{ A}$$
-Lastly, we look at node  $D$ . Incoming current is $I_{B\rightarrow D} $and$ I_{C\rightarrow D} $. Since there is no outgoing current defined yet,$ I_{D\rightarrow battery}$ must be outgoing to balance. To satisfy the Node Rule, we set
-$$I_{D\rightarrow battery} = I_{out} = I_{in} = I_{B\rightarrow D}+I_{B\rightarrow D} = 8 \text{ A}$$
-Notice that $I_{D\rightarrow battery}=I_1$. This will always be the case for currents going in and out of the battery (approximating a few things that are usually safe to approximate, such as a steady current). In fact, we could have treated the battery as another node in this example. Notice also that if you incorrectly reason about the direction of a current (incoming or outgoing), the calculation will give a negative number for the current. The Node Rule is self-correcting. A final diagram with directions is shown below.
+If instead, we made the other change, we would have tripled the cross-sectional area ($1 \text{ mm}^2 \rightarrow 3 \text{ mm}^2$). Our new resistance would then be $$R_{new} = \frac{L}{\sigma A_{new}} = \frac{L}{\sigma 3 A} = \frac{1}{3}R = 20 \text{ m}\Omega$$
-{{ 184_notes:6_nodes_with_arrows.png?300 |Circuit with Nodes}}
+These answers should make sense physically. The longer the wire, the more material there is for the electrons to push through, so the resistance is higher. The bigger the area, the more electrons are able to flow through the wire in at a given time so the resistance should be smaller.