Differences

This shows you the differences between two versions of the page.

--- 184_notes:induced_current [2021/04/08 18:52] – dmcpadden
+++ 184_notes:induced_current [2021/11/12 23:15] (current) – [Step 1.) Draw a picture of your situation] stumptyl
@@ Line 6: / Line 6: @@
 We will use the example of a bar magnet moving away from a wire coil to highlight these steps and to show how you can use a table to keep track of your work. While the specifics of the table will change depending on the context, the structure and steps will work no matter what problem you are solving. So to get started you should make a table like the one shown to the right with 8 columns. The first column will be for a picture/diagram of your situation, the second will be for the B-field direction, the third will be for the dA direction, the fourth will be for your initial magnetic flux, the fifth will be for the final magnetic flux, the sixth will be the change in magnetic flux, the seventh will be for your induced voltage, and the eighth will be for your induced current.
-[{{184_notes:inducedcurrent_blank.png?600|This is the table used for predicting the directional of the induced current.  }}]
+[{{184_notes:inductionchart_updated_11_12_2021.png?600|This is the table used for predicting the directional of the induced current.  }}]
+This video will walk you through an example of how to use this table or you can read about it in the notes below.
+{{youtube>Qlg0Iu1Do94?large}}
+\\
+**NOTE: In this chart there is a mistake in the chart being used: The variables "V" and "I" are not vectors. Please make a note of this when watching the video to ensure there is no confusion.**
 ==== Right Hand Rule Steps ====
@@ Line 14: / Line 18: @@
 Before anything, you should start with a picture of your situation. We'll draw this in the first column of the table. For our example, we'll have a bar magnet that is moving away from a set of coils. In the picture, we have marked the coils, the orientation of the magnet (which side is north/south), and which way the magnet is moving (marked with the velocity  $\vec{v}$  arrow).
-[{{184_notes:ic_scenario.png?440| Step 1: First make a diagram of the particular situation include the coil, magnet, and relevant directions.
+[{{184_notes:inductionchart_updated_11_12_2021.png?440| Step 1: First make a diagram of the particular situation include the coil, magnet, and relevant directions.
  }}]
@@ Line 21: / Line 25: @@
 Next we need to determine the direction of the magnetic field through the relevant area. For this situation, the relevant area is going to be our coils, so we are particularly interested in the direction of the B-field through the coils. Remember for a bar magnet, the magnetic field should point out from the north side of the magnet, wrap around, and point into the south side of the magnet. Since our coil is next to the south side of the magnet, this means the magnetic field inside the coil will mostly be pointing to the left (in towards the south side of the magnet). So in the second column we will put an arrow to the left.
-[{{184_notes:ic_bfield.png?440| Step 2: isolates the direction of the magnetic field and now places that corresponding vector into the chart. }}]
+[{{184_notes:inductionchart_partb.png?440| Step 2: isolates the direction of the magnetic field and now places that corresponding vector into the chart. }}]
@@ Line 28: / Line 32: @@
 Remember that the  $d\vec{A}$  is perpendicular to the cross section area of the coils. Meaning, that you can think of the  $d\vec{A}$  as pointing "out of” the coil. For our set up, this means that  $d\vec{A}$  could point either to the left or right (-x or +x direction). It doesn't matter which way you pick, as long as the  $d\vec{A}$  is perpendicular to the area. For this example, we'll pick the  $d\vec{A}$  to point to the left, so we draw an arrow in the third column that points to the left.
-[{{184_notes:ic_da.png?440| Step 3: Pick a direction for dA that points perpendicular to the coil. In this example, we pick  dA to be to the left.  }}]
+[{{184_notes:inductionchart_partc.png?440| Step 3: Pick a direction for dA that points perpendicular to the coil. In this example, we pick  dA to be to the left.  }}]
 ====Step 4.)  $\Phi_{B,i}$ ,  $\Phi_{B,f}$  and  $\frac{d\Phi_{B}}{dt}$ ====
@@ Line 34: / Line 38: @@
 The magnitude of the flux will depend on the size of the B-field and area at that particular time. For example if your bar magnet is close to your loop, you'd expect a big flux since the magnetic field is stronger closer to the magnet. The sign of the flux will be determined by the dot product of  $\vec{B}$  and  $d\vec{A}$ . Remember we can simplify the flux equation by saying:
- $\Phi_B = \int \vec{B} \bullet d\vec{A} = B *dA *cos(\theta)$
+$$\Phi_B = \int \vec{B} \bullet d\vec{A} = \int B *dA *cos(\theta)$$
 So if  $\theta$  is between  $0^\circ-90^\circ$ , then we know the flux will be positive. If  $\theta$  is between  $90^\circ-180^\circ$ , then the flux will be negative. So let's go through this for our example.
@@ Line 49: / Line 53: @@
 In our case, this means we'd be taking a small positive number minus a big positive number. This will result in a //negative// change in flux. (If it helps, you can assign numbers to help you think through this. For example, we could take  $2-10 = -8$ .) So we write down in the sixth column that the change in flux is negative.
-[{{184_notes:ic_flux.png
+[{{184_notes:inductionchart_partd.png
 ?440|Step 4: Determine the sign of the change in flux based on the initial and final flux for the situation.  }}]
 ====Step 5: Determining  $V_{ind}$ ====
-[{{ 184_notes:ic_vinduced.png
+Now that the direction of the $\frac{d \Phi_B}{dt}$  has been identified, we can simply flip the sign for the V-induced. We have to do this step because there is a negative sign in Faraday's Law:
-?440|Step 4 of the solution process. The sign of the V-induced is the **opposite** of the change in flux.}}]
+$$V_{ind} = -\frac{d \Phi_B}{dt}$$
-[{{ 184_notes:inducedcurrentscenario_final.png
+For our example, the change in flux was negative. So we write down "positive" for the  $V_{ind}$  column.
-?440|Step 5 of the solution process. This allows for the description of the motion of the induced current to be highlighted and place within the chart.}}]
-\\
+[{{184_notes:inductionchart_parte.png
+?440|Step 5: The sign of the V-induced is the **opposite** of the change in flux.  }}]
+====Step 6: Determining the direction of  $I_{ind}$ ====
+Our final step then is to determine the direction of the induced current! This is where the right hand rule part comes in. But what does it mean for  $V_{ind}$  to be positive or negative? Ultimately this goes back to our choice of  $d\vec{A}$  at the beginning. So there will be two scenarios:
+  * If  $V_{ind}$  is positive, you should put the thumb of your right hand in the **same direction as your  $d\vec{A}$ **. Then the way that you curl your fingers will show the direction of the induced current.
+  * If  $V_{ind}$  is negative, you should put the thumb of your right hand in the **opposite direction as your  $d\vec{A}$ **. Then the way that you curl your fingers will show the direction of the induced current.
-=====Concluding=====
+For our example, we found that $V_{ind}$ was positive. So this means that we would stick our thumb in the -x direction (pointing to the left) and then curl our fingers around in a circle. You should find the the current would go into the page at the top of the coil and would come back out of the page at the bottom of the coil. Just because it's often hard to draw the current direction in 3D, we often will just notate where on the coil the current is into/out of the page.
-$\frac{d \Phi_B}{dt}$, remember, is the change in flux over a given time. Meaning that we need to calculate and understand the change of the flux as we start and end the scenario. Since these were generalizations given to find flux, the only thing we need for this approach is the sign of the change in flux. Meaning if I have a “Big Positive Initial Flux” (i.e. the B-Field and the  $d\vec{A}$  are in the same direction and very close together at the beginning of the scenario) and then have a “Small Positive Final Flux” (i.e. the B-Field and the  $d\vec{A}$  are in the same direction and relatively farther away at the end of the scenario). This change would result in a final  $\frac{d \Phi_B}{dt}$   of a negative number. (Final – initial with the large value being in the latter.) Now that the direction of the  $\frac{d \Phi_B}{dt}$   has been identified, we can flip the sign for the V-induced.
-\\
-\begin{align*}
--\int \vec{E}_{nc} \bullet d\vec{l} &= \frac{d \Phi_B}{dt} &&&& (1) \\
--V_{ind} &= \frac{d \Phi_B}{dt} &&&& (2) \\
-\end{align*}
-\\
-This is now a built in check to see if the predicted  $d\vec{A}$  was correct! __**If the V-induced value is positive, then your right hand will stay in the same direction that you started with. If the V-induced value is negative, then you must flip your hand to go in the opposite direction.**__ Now that we have the properly identified  $d\vec{A}$ , we can utilize the Right Hand Rule Method to describe the direction of the I-induced.
-\\
-Remember that the thumb represents the $d\vec{A}$ and the curl of your fingers describes the rotational direction that the current will flow. In our example, since the  $d\vec{A}$  points in the positive x-direction and the V-induced was positive, Meaning that if the induced current was occurring in the z-direction, we would label the answers as either “Into the page, then Out of the Page” or vice versa to describe the direction of flow. By utilizing this approach, students are able to have a formal methodology for approaching how to describe the directionality of the Induced Current.
+[{{184_notes:inductionchart_partf.png
+?440|Step 6: Find the direction of the induced current based on the right hand rule. }}]
+The right hand rule for determining the induced current direction is definitely more complicated than our previous right hand rules; however, this table helps break the process down into manageable chunks. We definitely recommend writing out each step in this way - otherwise it is easy to miss a step or a negative sign, which will throw off your final result.