Differences

This shows you the differences between two versions of the page.

--- 184_notes:r_energy [2017/10/03 19:55] – [Energy around the Circuit] pwirving
+++ 184_notes:r_energy [2021/06/14 23:41] (current) – schram45
@@ Line 1: / Line 1: @@
 Sections 18.3, 18.8-18.10, and 19.4 in Matter and Interactions (4th edition)
-===== Resistors in Circuits =====
+/*[[184_notes:resistivity|Next Page: Resistors and Conductivity]]
-To this point, we have talked about what happens inside a wire when connected to two ends of battery - both in the steady state current situation and in the initial transient when the circuit is first connected. We found a few important conclusions about the circuit in steady state:
-  * The electron current going into a location must be the same as the current leaving that location because charge is conserved.
-  * The electron current moves through the wire because there is a constant electric field inside the wire. This electric field comes primarily from the surface charges along the wire.
-  * The distribution of surface charges varies along the wire - from highly positive near the positive end of the battery to zero in the middle of the circuit to highly negative near the negative end of the battery. This gradient in the surface charge density causes the electric field inside the wires.
- These notes will apply what we learned about the electric field, current, and surface charges to what we call a resistor and discuss what happens to energy around the circuit.
+[[184_notes:resistors|Previous Page: Resistors]]*/
-{{youtube>1P5M1OIq8Ho?large}}
+===== Energy around the Circuit =====
-==== A Thin Resistor ====
+One of the consequences of adding a resistor in the circuit (with higher electron speed and a higher electric field) is that a large **energy transfer** occurs across the resistor. In thin wire resistors (sometimes referred to as filaments), this effect is particularly visible. The amount of energy transferred to a filament is sufficient to heat the thin wire to the point where it produces heat and light. This is actually how [[https://en.wikipedia.org/wiki/Incandescent_light_bulb|incandescent light bulbs]] work.
-{{184_notes:thinresistorcircuit.jpg?150  }}
-We'll start with a similar circuit as last week - a battery connected by a wire; however, in the middle of the wire, we'll make a part that is much thinner than the rest of the wire (but still made of the same material). We'll call this narrow section a **resistor**. //Note that real resistors are not simply thin pieces of metal, but this is the simplest model of a resistor and it helps us to understand the general concepts of resistance.// We'll show that a resistor is a section or part of a circuit that resists the passage of electrons more than in other parts of the circuit. These notes will try to address the question: what happens to the surface charges and electric field around this thin section of wire?
+{{youtube>c4tAtICY2Co?large}}
-==== Conservation of Charge in Circuits ====
+Let's continue to look at the simple circuit that we were using in the video above (a mechanical battery, wires, and a thin filament). To analyze the energy in our circuit, we can refer back to [[184_notes:three_principles|the Energy Principle]]. If we take everything to be in our system, including the battery, wires, filament, and the surrounding air or materials, then we know that:
-{{  184_notes:ThinResistorChargeDistribution.jpg?250}}
-=== Before steady state ===
-Just after the circuit is connected, //__before the steady state current is established__//, there would be a constant electric field set up in the wire, which would start to move the electrons in the wire (with some average speed  $v_{avg}$ ) and create the electron current. At this point, the number of electrons per second trying to enter the thin resistor is fairly large, compared to the number of electrons per second that can pass through the resistor. This means that the electrons pile up on one side of the resistor (and there is a similar lack of negative charges on the other side), creating a larger electric field within the resistor than that in the nearby wires. The electrons that pile up generate an electric field that opposes the motion of the electrons attempting to enter the resistor. At this point in time the current going into the resistor //**does not**// equal the current going through the resistor (e.g. the node rule does not apply), but this because we are looking at the situation //__before the circuit is in a steady state__//. (Charge is still conserved in this situation - it's just that some of the charge are piling up on the surface rather than passing through the thin part of the wire.) The electrons will continue to pile up until a steady state current is reached.
-=== In steady state ===
-Once a //__steady state current is reached__//, we know that the current in the resistor (or thin part of the wire) must be the same as the current in the thick part of the wire. In the steady state, charge has already built up on the ends of the resistor to create a larger electric field and no more charge is added to the surface at this point. If the charges aren't moving to the surface, conservation of charge says that all of the charges passing through the large part of the wire must also pass through the thin part of the wire.
-Using [[184_notes:current|the current relationships]], we can show that the electric field and therefore drift speed must be larger inside the resistor to maintain the same current.
- $i_{thin}=i_{thick}$
- $n A_{thin} u E_{thin}= n A_{thick} u E_{thick}$
-Since the thin and thick wires are made of the same materials, the electron density and electron mobility is the same, which leaves:
- $E_{thin}=\frac{A_{thick}}{A_{thin}}E_{thick}$
-{{184_notes:thinresistorefield.jpg?200  }}
-Since  $A_{thick}>A_{thin}$ , this means that the electric field will be bigger in the thin section of wire compared to the thick wires. Because  $v_{avg}=uE$ , this also means that the average speed of the electrons in the thin wire must also be bigger than the average speed in the thick wires. Ultimately, this means that in the steady state situation, the largest surface charge gradient occurs over the resistor, with only small gradients in the thick wires.
-As noted above, a thin wire resistor is only one kind of resistor. You could also have a resistor in a circuit made out of a different material, but still the same size as the thick wires. Or both a different size and a different material. Resistors come in a wide variety of shapes, sizes, and materials. In these cases, the electron density and electron mobility of the materials matter much more to current analysis in the circuit.
-==== Energy around the Circuit ====
-{{youtube>c4tAtICY2Co&?large}}
-One of the consequences of adding a resistor in the circuit (with higher electron speed and a higher electric field) is that a large energy transfer occurs across the resistor. In thin wire resistors (sometimes referred to as filaments), this effect is particularly visible. The amount of energy transferred to a filament is sufficient to heat the thin wire to the point where it produces heat and light. This is actually how [[https://en.wikipedia.org/wiki/Incandescent_light_bulb|incandescent light bulbs]] work.
-Let's continue to look at the simple circuit that we were using above (a mechanical battery, wires, and a thin filament). To analyze the energy in our circuit, we can refer back to the [[184_notes:three_principles|the Energy Principle]]. If we take everything to be in our system, including the battery, wires, filament, and the surrounding air or materials, then we know that:
  $\Delta E_{sys}=0$
 If we breakdown what is in our system, this means that
@@ Line 49: / Line 16: @@
 From this statement of energy conservation, this would tell us that any energy provided by the battery must be used in the wires, heating up the filament, or providing light and heat to the surroundings.
-=== Energy per unit charge: Electric Potential ===
+==== Energy per unit charge: Electric Potential ====
 We could also consider what is happening to the energy of a single electron as it makes a complete trip around the circuit. The energy gained by the electron as it is transported across the mechanical battery is dissipated by the collisions the electron has as it moves around the wire, particularly with the positive nuclei in the wire. While this is certainly true, it becomes cumbersome to think about every single electron that is moving around the circuit. Instead, we will often think about energy in circuits in terms of the energy per charge that is moving around the circuit. [[184_notes:pc_energy#General_Relationship_-_Energy_and_Potential|As we talked about before]], **electric potential //is// the energy per charge**, which is something that you have been working with over the last few weeks. So rather than talk about changes in energy around the circuit, we will generally be talking about changes in electric potential around the circuit.
-This means we can rewrite our energy conservation statement in terms of the energy per charge instead. This is called **The Loop Rule** or sometimes Kirchhoff's Loop Rule. This Loop Rule says that if you follow a complete, round-trip path in a circuit, the total change in electric potential across all of the circuit elements (i.e., batteries, wires, resistors, capacitors) should be zero.
+This means we can rewrite our energy conservation statement in terms of the energy per charge instead. This is called **//The Loop Rule//** or sometimes Kirchhoff's Loop Rule. This Loop Rule says that if you follow a complete, round-trip path in a circuit, the total change in electric potential across all of the circuit elements (i.e., batteries, wires, resistors, capacitors) should be zero.
  $\Delta V_1+\Delta V_2+\Delta V_3+...=0$
@@ Line 61: / Line 28: @@
 Another way to talk about energy in circuits is to look at how much energy (aka, heat or light) is used up per second by a lightbulb or more generally by a resistor (in contrast to voltage which is energy per charge). When you are talking about the change in energy per change in time, this is called **power**:
  $P=\frac{\Delta U}{\Delta t}=\frac{dU}{dt}$
-Power is a scalar quantity that has units of watts or joules per second ( $W=\frac{J}{s}$ ). For reference, a typical lightbulb in your house is a 60 W lightbulb. On the other hand, a large power plant that produces electricity for a city generally produces  $1-5$  MW  $=1-5 \cdot 10^6$ W. In circuits, it is fairly easy to calculate the power if you know the potential difference across a circuit element and the current that passes through that element. To get power, you multiply current times the potential difference since current has units of amps or coulombs per second, and electric potential has units of volts.  $\frac{C}{s}*V=\frac{J}{s}$  since a volt*coulomb is a joule, we get units of energy per second, which is what we want.  In other words,
+Power is a scalar quantity that has **units of watts or joules per second** ( $W=\frac{J}{s}$ ). For reference, a typical lightbulb in your house is a 60 W lightbulb. On the other hand, a large power plant that produces electricity for a city generally produces  $1-5$  MW  $=1-5 \cdot 10^6$ W. In circuits, it is fairly easy to calculate the power if you know the potential difference across a circuit element and the current that passes through that element. To get power, you multiply current times the potential difference since current has units of amps or coulombs per second, and electric potential has units of volts.  $\frac{C}{s}*V=\frac{J}{s}$  since a volt*coulomb is a joule, we get units of energy per second, which is what we want.  In other words,
  $P=I\Delta V$
 Note we are using conventional current here, not the electron current.
 ==== Examples ====
-What happens to E-field, resistance, and power if you double length of wire? What happens if you double the area?
+  * [[:184_notes:examples:Week7_wire_dimensions|Changing the Dimensions of a Wire]]
+    * Example Video: Changing the Dimensions of a Wire
+{{youtube>uRIzyLqRtRU?large}}