184_notes:ac

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
184_notes:ac [2017/11/28 22:47] – [Voltage Transformer] dmcpadden184_notes:ac [2021/07/13 13:30] (current) – schram45
Line 1: Line 1:
 Section 22.2 in Matter and Interactions (4th edition) Section 22.2 in Matter and Interactions (4th edition)
 +
 +/*[[184_notes:changing_e|Next Page: Changing Electric Fields]]
 +
 +[[184_notes:b_flux_t|Previous Page: Changing Magnetic Fields with Time]]*/
 +
 ===== Changing Flux from an Alternating Current ===== ===== Changing Flux from an Alternating Current =====
 As we said before, one of the most important sources of a changing magnetic field is an alternating current. This is what actually comes out of the wall outlets; as opposed to the current from a battery which is a constant current (or a direct current). We are only briefly going to talk about alternating current as it refers to induction and changing magnetic flux, but there are many more applications of alternating current, especially with regard to circuits, resistors, and capacitors. For the purposes of these notes, we will talk about how we represent an alternating current, how that alternating current can produce an induced current/potential, and how that applies to voltage transformers. As we said before, one of the most important sources of a changing magnetic field is an alternating current. This is what actually comes out of the wall outlets; as opposed to the current from a battery which is a constant current (or a direct current). We are only briefly going to talk about alternating current as it refers to induction and changing magnetic flux, but there are many more applications of alternating current, especially with regard to circuits, resistors, and capacitors. For the purposes of these notes, we will talk about how we represent an alternating current, how that alternating current can produce an induced current/potential, and how that applies to voltage transformers.
  
-==== Alternating Current ==== +===== Alternating Current ===== 
-{{  184_notes:Week14_6.png?200}}+[{{  184_notes:Week14_6.png?200|Current over time in an alternating current cycle}}]
  
 When a current is constantly switching between positive and negative values, we call this an **alternating current**. Typically, this means that we have a current that is represented by a sine graph (shown in the figure to the right), though there can be other types of alternating current that look like step functions (also called [[https://en.wikipedia.org/wiki/Square_wave|square waves]]) or triangular shapes (or [[https://en.wikipedia.org/wiki/Triangle_wave|triangle waves]]). We will stick with a sine graph because it is mathematically easier to manipulate and is the most common kind of alternating current. This means that we represent the current as: When a current is constantly switching between positive and negative values, we call this an **alternating current**. Typically, this means that we have a current that is represented by a sine graph (shown in the figure to the right), though there can be other types of alternating current that look like step functions (also called [[https://en.wikipedia.org/wiki/Square_wave|square waves]]) or triangular shapes (or [[https://en.wikipedia.org/wiki/Triangle_wave|triangle waves]]). We will stick with a sine graph because it is mathematically easier to manipulate and is the most common kind of alternating current. This means that we represent the current as:
Line 14: Line 19:
 This means that a larger period would be related to a smaller frequency, and a smaller period would be related to a higher frequency. Since the period is often easier to think about conceptually, it may be easier to start with period (from a graph for example) and then relate it back to the frequency.    This means that a larger period would be related to a smaller frequency, and a smaller period would be related to a higher frequency. Since the period is often easier to think about conceptually, it may be easier to start with period (from a graph for example) and then relate it back to the frequency.   
  
-==== Voltage Transformer ====+===== Voltage Transformer =====
 If you have an oscillating current, this would also mean that you would have an oscillating magnetic field everywhere around the wire (since currents create magnetic fields). If there is an oscillating magnetic field, this means that there will also be an induced potential/current in any nearby loop of wire since the magnetic field would be constantly changing. One common application of this idea is called a step-up transformer (or alternatively a step-down transformer), which is crucial to getting electricity from the power generator to your house. If you have an oscillating current, this would also mean that you would have an oscillating magnetic field everywhere around the wire (since currents create magnetic fields). If there is an oscillating magnetic field, this means that there will also be an induced potential/current in any nearby loop of wire since the magnetic field would be constantly changing. One common application of this idea is called a step-up transformer (or alternatively a step-down transformer), which is crucial to getting electricity from the power generator to your house.
  
-{{184_notes:power_transformer.jpg?200  }}+[{{184_notes:power_transformer.jpg?200|Power transformer  }}]
  
 As you figured out in the project last week, a rotating loop in a magnetic field will create a oscillating current and oscillating voltage. This idea is exactly what happens in a power generator, just on a much larger scale. In a power generator there are thousands of loops, rotating very quickly in a large magnetic field to produce a very large current with a frequency of 60 Hz (in the U.S. at least). However, because power (or the energy transferred to heat) is related to $P=I^2R$, sending a very large current over large distances (like from the generator to your house) would result in a large loss of power over that wire. This is a problem because any power lost on the wires can't be used in your house and if that power is large enough it could heat up the wires to point where they are damaged.   As you figured out in the project last week, a rotating loop in a magnetic field will create a oscillating current and oscillating voltage. This idea is exactly what happens in a power generator, just on a much larger scale. In a power generator there are thousands of loops, rotating very quickly in a large magnetic field to produce a very large current with a frequency of 60 Hz (in the U.S. at least). However, because power (or the energy transferred to heat) is related to $P=I^2R$, sending a very large current over large distances (like from the generator to your house) would result in a large loss of power over that wire. This is a problem because any power lost on the wires can't be used in your house and if that power is large enough it could heat up the wires to point where they are damaged.  
Line 23: Line 28:
 To get around this problem, a step up transformer is used to change a low voltage, high current circuit (like what comes out the generator) into a high voltage, low current circuit for transport from the generator to the neighborhoods or wherever it is needed. A step down transformer is then used close to the neighborhoods to return the high voltage, low current back to a low voltage, high current circuit that is then used in your house. You may have seen these around your neighborhood - they look like small boxes attached to the power lines overhead, generally on the lines going from a larger street into a residential area (shown in the figure to the left). To get around this problem, a step up transformer is used to change a low voltage, high current circuit (like what comes out the generator) into a high voltage, low current circuit for transport from the generator to the neighborhoods or wherever it is needed. A step down transformer is then used close to the neighborhoods to return the high voltage, low current back to a low voltage, high current circuit that is then used in your house. You may have seen these around your neighborhood - they look like small boxes attached to the power lines overhead, generally on the lines going from a larger street into a residential area (shown in the figure to the left).
  
-{{  184_notes:week14_7.png?400}}+[{{  184_notes:week14_7.png?400|Primary and Secondary solenoids in a step-up transformer}}]
  
 In these notes, we will go through how a step up transformer works and how it uses induction to change the voltage from a low voltage to a high voltage. We will use a basic transformer, which is essentially two solenoids wrapped around a iron ring (shaped like doughnut), as shown in the figure to the right. The first solenoid, which will refer to as the primary solenoid, is connected to the power generator and has the low voltage (and high current). The second solenoid, which we will refer to as the secondary solenoid, should then have a high voltage (and low current) and eventually be connected to the city through a step down transformer.   In these notes, we will go through how a step up transformer works and how it uses induction to change the voltage from a low voltage to a high voltage. We will use a basic transformer, which is essentially two solenoids wrapped around a iron ring (shaped like doughnut), as shown in the figure to the right. The first solenoid, which will refer to as the primary solenoid, is connected to the power generator and has the low voltage (and high current). The second solenoid, which we will refer to as the secondary solenoid, should then have a high voltage (and low current) and eventually be connected to the city through a step down transformer.  
  
-{{184_notes:Week14_8.png?400  }}+[{{184_notes:Week14_8.png?400|Induced magnetic field  }}]
    
 Because there is an oscillating potential/current in the first solenoid (from the generator), this will create a constantly changing magnetic field in the primary solenoid. Since the primary solenoid is wrapped around the iron bar, the magnetic field from the solenoid will cause all of the atoms within the iron to align with the magnetic field from the primary solenoid. Because iron atoms are very responsive to magnetic fields, even the atoms that are outside the primary solenoid will align with this magnetic field (largely because they are feeling the effects of their neighboring iron atoms). Since iron is easily magnetized, we will //__assume that the magnetic field in the iron from the primary solenoid will be the same magnetic field in the secondary solenoid__// (still in the iron ring). Because the magnetic field in the primary solenoid is oscillating, this means that the magnetic field in all of the iron ring is also constantly changing.  Because there is an oscillating potential/current in the first solenoid (from the generator), this will create a constantly changing magnetic field in the primary solenoid. Since the primary solenoid is wrapped around the iron bar, the magnetic field from the solenoid will cause all of the atoms within the iron to align with the magnetic field from the primary solenoid. Because iron atoms are very responsive to magnetic fields, even the atoms that are outside the primary solenoid will align with this magnetic field (largely because they are feeling the effects of their neighboring iron atoms). Since iron is easily magnetized, we will //__assume that the magnetic field in the iron from the primary solenoid will be the same magnetic field in the secondary solenoid__// (still in the iron ring). Because the magnetic field in the primary solenoid is oscillating, this means that the magnetic field in all of the iron ring is also constantly changing. 
  
-{{  184_notes:Week14_9.png?400}}+[{{  184_notes:Week14_9.png?400|Cross sectional area of the iron ring would be dA in our calculation}}]
  
 If we put the secondary solenoid on the end of the iron ring, this changing magnetic field will be the same as that from the primary solenoid: $B_P=B_S$. This changing magnetic field (from the primary solenoid) will induce a voltage ($V_S$) in the secondary solenoid. We can use Faraday's Law to write this as: If we put the secondary solenoid on the end of the iron ring, this changing magnetic field will be the same as that from the primary solenoid: $B_P=B_S$. This changing magnetic field (from the primary solenoid) will induce a voltage ($V_S$) in the secondary solenoid. We can use Faraday's Law to write this as:
Line 63: Line 68:
  
 ==== Examples ==== ==== Examples ====
-/* +  * [[:184_notes:examples:Week14_ac_graph|Analyzing an Alternating Current Graph]] 
-[[:184_notes:examples:Week14_ac_graph|Analyzing an Alternating Current Graph]]+  * [[:184_notes:examples:Week14_step_down_transformer|Designing a Step-down Transformer]] 
 +    * Video Example: Designing a Step-Down Transformer 
 +{{youtube>NAngoOBjCSA?large}}
  
-[[:184_notes:examples:Week14_step_down_transformer|Designing a Step-down Transformer]] 
-*/ 
  • 184_notes/ac.1511909267.txt.gz
  • Last modified: 2017/11/28 22:47
  • by dmcpadden